Well,
Been fiddling around at home today and building a bench RF Signal Generator. I have a homebrew one already but it's a bit hit and miss to tune, I also have an old Avo valve based signal generator, but that's extremely heavy, very large and generates lots of heat!
I saw a schematic for a suitable bench Signal Generator a while ago in Experimental Methods in RF Design (page 7.15 Fig 7.27), so I thought I would have a go at making one.
Here's what it looks like in it's current state of construction:
The tuning capacitor on the RHS is the main tuning and the second variable capacitor on the LHS is the fine tuning; that should help make it easier to set the device.
The toroid you can see nearest the front of the picture above is a little odd; the secondary is just a single turn which in reality is the leg of the diode you can see just passing through the centre.
I then found in my box labeled "projects" a digital dial kit from QRP kits:
http://www.qrpkits.com/freqcounter.html
I've used these in projects in the past and I must have ordered an extra one some time ago, anyhow as this is a surface mount project, it was extreme soldering time again. If anyone doesn't realise how small these components are, here's one of the resistors on my thumb nail:
So, here is the underside of the project board completed:
And the display side:
Ideally you would calibrate this with as high a frequency as possible, but I have used my 10MHz frequency standard from here:
http://g0mgx.blogspot.co.uk/2011/07/ocxo-oh-you-mean-ocxo.html
And here is the counter connected to the signal generator, I've added an additional buffer output stage between the output PAD and the counter in my build:
So, the output of the new bench Signal Generator looks quite good, here's some shots of the device set at 10MHz exactly:
This now needs a case, but I am going to wait until the end of the month when I will be at the National Hamfest and see if I can find anything there. I'm away between now and then in A71 land so it will just have to wait.
There is an expression about curiosity and cats:
Good though, egh?
Been fiddling around at home today and building a bench RF Signal Generator. I have a homebrew one already but it's a bit hit and miss to tune, I also have an old Avo valve based signal generator, but that's extremely heavy, very large and generates lots of heat!
I saw a schematic for a suitable bench Signal Generator a while ago in Experimental Methods in RF Design (page 7.15 Fig 7.27), so I thought I would have a go at making one.
Here's what it looks like in it's current state of construction:
The tuning capacitor on the RHS is the main tuning and the second variable capacitor on the LHS is the fine tuning; that should help make it easier to set the device.
The toroid you can see nearest the front of the picture above is a little odd; the secondary is just a single turn which in reality is the leg of the diode you can see just passing through the centre.
I then found in my box labeled "projects" a digital dial kit from QRP kits:
http://www.qrpkits.com/freqcounter.html
I've used these in projects in the past and I must have ordered an extra one some time ago, anyhow as this is a surface mount project, it was extreme soldering time again. If anyone doesn't realise how small these components are, here's one of the resistors on my thumb nail:
So, here is the underside of the project board completed:
And the display side:
Ideally you would calibrate this with as high a frequency as possible, but I have used my 10MHz frequency standard from here:
http://g0mgx.blogspot.co.uk/2011/07/ocxo-oh-you-mean-ocxo.html
And here is the counter connected to the signal generator, I've added an additional buffer output stage between the output PAD and the counter in my build:
So, the output of the new bench Signal Generator looks quite good, here's some shots of the device set at 10MHz exactly:
This now needs a case, but I am going to wait until the end of the month when I will be at the National Hamfest and see if I can find anything there. I'm away between now and then in A71 land so it will just have to wait.
There is an expression about curiosity and cats:
Good though, egh?
No comments:
Post a Comment