Well,
Been fiddling a bit more this evening and have interfaced the si570 silicon labs device:
http://www.silabs.com/Support%20Documents/TechnicalDocs/si570.pdf
Now, I haven't ever used one of these before, but I happened to have one here. I verified that it was a CMOS 3.3V variant (there are lots of different types) and then thought about how to connect to the thing - it's very, very small.
So, the first thing I did was find some off cuts from resistors on my bench and solder them to the device which I held in place with some trusty blue tac:
I then assembled the pull-up resistors and the coupling caps on a bit of copper board:
NOW THIS BIT IS VERY IMPORTANT because the si570 is a 3.3V device I have had to modify the file TWI.c to remove software 5V pull-ups on the two interface lines, as I am using a Mega2560 board I HAVE HAD TO PHYSICALLY REMOVE ON BOARD PULL UP RESISTORS also. I have documented the details of the mod on the Minima Wiki here:
http://www.hfsignals.org/index.php/Radiono
If you don't do this then I suspect the 5V pull ups will result in bye bye si570.
So, I connected it up to the Mega2560 and connected a 50R terminated 'scope to the capacitor leg you can see in the image above, this is with the scope bandwidth limit enabled:
Here, with a x10 probe and no 50R termination:
here, with a x1 probe and no 50R termination:
and here with a x1 probe and a 50R termination:
here's the signal on the Spectrum Analyser:
And here, for comparison, is a 34MHz signal out of an AD9851 Arduino controlled DDS I made back here:
http://g0mgx.blogspot.co.uk/2012/02/dds-running-well.html
and it looks like this:
CW Cat hasn't been helping much today:
Good though, egh?
Been fiddling a bit more this evening and have interfaced the si570 silicon labs device:
http://www.silabs.com/Support%20Documents/TechnicalDocs/si570.pdf
Now, I haven't ever used one of these before, but I happened to have one here. I verified that it was a CMOS 3.3V variant (there are lots of different types) and then thought about how to connect to the thing - it's very, very small.
So, the first thing I did was find some off cuts from resistors on my bench and solder them to the device which I held in place with some trusty blue tac:
I then assembled the pull-up resistors and the coupling caps on a bit of copper board:
NOW THIS BIT IS VERY IMPORTANT because the si570 is a 3.3V device I have had to modify the file TWI.c to remove software 5V pull-ups on the two interface lines, as I am using a Mega2560 board I HAVE HAD TO PHYSICALLY REMOVE ON BOARD PULL UP RESISTORS also. I have documented the details of the mod on the Minima Wiki here:
http://www.hfsignals.org/index.php/Radiono
If you don't do this then I suspect the 5V pull ups will result in bye bye si570.
So, I connected it up to the Mega2560 and connected a 50R terminated 'scope to the capacitor leg you can see in the image above, this is with the scope bandwidth limit enabled:
Here, with a x10 probe and no 50R termination:
here, with a x1 probe and no 50R termination:
and here with a x1 probe and a 50R termination:
here's the signal on the Spectrum Analyser:
And here, for comparison, is a 34MHz signal out of an AD9851 Arduino controlled DDS I made back here:
http://g0mgx.blogspot.co.uk/2012/02/dds-running-well.html
and it looks like this:
CW Cat hasn't been helping much today:
Good though, egh?
